Sentry Sentry Xpress Sentry Xpress 4.0 Instrukcja Obsługi Pobierz pdf

The Sentry Xpress 4.0 micro processor is manufactured by the

Orton Ceramic Foundation and displays the CE mark.

Hr./Min.

When Lit

HIGHER

°C

°F

When Off

When Lit

START/

STOP

LOWER

Program

Review

Run

MICRO PROCESSOR

SENTRYXpress

4.0

Enter

Program

Skip Seg.

Add Hold

Change Temp.

T/C Offset

Alarm

Delay

Review

START/STOP Key

Starts and stops a firing.

Press after each

programming step. It works like the

Enter key on a computer.

Down Arrow Key

From press

.Theprogram

you have selected will ap-

pear one step at a time.

When appears,

press .Page4

From

press .

Enter delay time. Press

.Page4

During firing, press

. The program you

entered will appear one

step at a time. Page 4

Indicator

Lights

Temperature Display

Tempera

ture display is in °F.

Temperature display is in °C.

Seepage13forinstructions

on selecting °F and °C.

Time Display

:Sepa-

rates hours from minutes. Ex-

ample: Display shown above

is 1 hour and 30 minutes.

°C Display Dot

Cone Fire/Ramp-Hold Version

°F

°C

Sentry Xpress

Digital Temperature Controller

IM-222/5-11

Light is

on during pro

gramming.

Light is

on during pro

gram review.

Light

blinks during firing.

Up Arrow Key

From

press .Press

to select Cone-Fire or

Ramp-Hold. Pages 6, 8

During a

Ramp-Hold firing, press the

. will appear. Press

. The current segment

ramp or hold number will ap

pear. To skip, press

again. Page 10

During a

Ramp-Hold firing, press

repeatedly until ap

pears. Press .Eachtime

you press the ,the

hold time for the current seg

ment will increase by 5 minutes.

Then press .

Page 10

During a Ramp-Hold firing,

press repeatedly until

appears. Press .

Use the arrow keys to change

the target temperature for the

current segment. Then press

.Page10

During a fir

ing, press repeatedly

until appears. Press

. Use the arrow keys to

change the alarm temperature.

Press .Tosilencethe

alarm, press any key. Page 10

At the display,

press . will ap

pear. Use arrow keys to adjust

the controller to fire hotter or

cooler. Press to return to

.Page13

*These features are new with the Sentry Xpress 4.0. This manual,

nevertheless, is backward compatible with earlier controllers.

1 2 3 4 5 6 ... 19 20

Podsumowanie treści

Strona 1 - Sentry Xpress

The Sentry Xpress 4.0 micro processor is manufactured by theOrton Ceramic Foundation and displays the CE mark.Hr./Min.When LitHIGHER°C°FWhen OffWhen L

Strona 2 - Introduction

10 Cone-Fire / Ramp-HoldEditing the TargetTemperatureWhile the kiln is firing, you can change the target tem-perature. You can edit only the segment t

Strona 3 - Guidelines

11Segment 3 lowers temperature to 800°F / 426°C, the typi-cal casting temperature for silver. (Most types of gold castat 900°F / 482°C.)Note: Casting

Strona 4 - 4 Cone-Fire / Ramp-Hold

12 Cone-Fire / Ramp-HoldTo return to from an FE codeTrypressingany key. If that doesn’t work, turn thepoweroff for 10 seconds. Call the factory if the

Strona 5 - Cone-Fire

13PF 3 / Power FailureThe powerfailedduring firing and temperaturedroppedmore than 72°F / 40°C by the time the power came back on.The kiln will not re

Strona 6 - Cone-Fire Hold

Cone-Fire Schedules - °FSelecting a Fast speed in Cone-Fire increases the segment rates shown in this chart by 20%. Selecting a Slow speed de-creases

Strona 7 - Ramp-Hold

15Cone-Fire Schedules - °CSelecting a Fast speed in Cone-Fire increases the segment rates shown in this chart by 20%. Selecting a Slow speed de-crease

Strona 8 - Ramp-Hold Programming

16 Cone-Fire / Ramp-HoldTemperature Equivalents ForOrton Self-Supporting Pyrometric Cones°FCone Self-Supporting Cones Pre-FireNum-ber ColorHeated at:

Strona 9

17DisplayMessagesThe firing was stopped.(Page 10) Ready for you to enter an alarm temper-ature. When the kiln reaches that temperature, the alarmwill

Strona 10 - Features

18 Cone-Fire / Ramp-Holdfacing you. Plug the kiln back in. Touch voltmeter probes(in AC mode) to both INPUT connections (the white andorange wires).CA

Strona 11 - Lost Wax

19IndexAbrt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Add Hold Time. . . . . . . . . . . . . . . . . . . . .

Strona 12 - Error Messages

2 Cone-Fire / Ramp-HoldContentsGeneral Guidelines . . . . . . . . . . . . . . . . . 3Time and Temperature Displays . . . . . . . . . . . . . . . . . .

Strona 13 - °C Display

20 Cone-Fire / Ramp-HoldShorthand InstructionsThese instructions may be confusing until you have read more detailed instructions on Cone-Fire, page 6,

Strona 14 - Cone-Fire Schedules - °F

3GeneralGuidelinesTime and TemperatureDisplaysCenter Dot: TimeA center dot appears dur-ing time display. It separateshours from minutes (Exam-ple: 1 h

Strona 15 - Cone-Fire Schedules - °C

4 Cone-Fire / Ramp-HoldPower FailuresAfter a power failure, the controller will continue firingprovided that:IThe kiln temperature is above 212°F / 10

Strona 16 - Temperature Equivalents For

5We suggest using the witness cone to trouble shoot prob-lems with the ware. If china paints appear faded and yoususpect it is due to over-firing, tes

Strona 17 - Trouble Shooter

6 Cone-Fire / Ramp-HoldCone-Fire ProgrammingInstructionsFrom , press (the left button).Using the key (not the ),skip past and se-lect . Then press .Th

Strona 18 - Problem: Kiln switch box ½

7Ramp-HoldModeTheory of OperationThe temperature you are firing to is called the targettemperature. After the controller reaches the target tem-peratu

Strona 19 - Problem: The kiln overfires

8 Cone-Fire / Ramp-HoldStoring ProgramsThe controller can retain four Ramp-Hold programs inmemory even when power is turned off. Programs are num-bere

Strona 20 - Shorthand Instructions

9HoldHold is the length of time that you want the kiln to re-main at the target temperature. Hold is also called soak ordwell time. Hold maintains a s